[1]蒋大勇,郭三学.前混合磨料水射流对HTPB推进剂的切割工艺参数优化研究[J].365bet在线网址_365bet网上娱乐网址_365bet手机网址多少,2019,48(04):47-53.[doi:10.3969/j.issn.1001-8352.2019.04.009]
 JIANG Dayong,GUO Sanxue.Cutting Efficiency and Process Parameter Optimization of Premixed Abrasive Water Jet to HTPB Propellant[J].EXPLOSIVE MATERIALS,2019,48(04):47-53.[doi:10.3969/j.issn.1001-8352.2019.04.009]
点击复制

前混合磨料水射流对HTPB推进剂的切割工艺参数优化研究()
分享到:

《365bet在线网址_365bet网上娱乐网址_365bet手机网址多少》[ISSN:1001-8352/CN:32-1163/TJ]

卷:
48
期数:
2019年04
页码:
47-53
栏目:
爆炸材料
出版日期:
2019-07-04

文章信息/Info

Title:
Cutting Efficiency and Process Parameter Optimization of Premixed Abrasive Water Jet to HTPB Propellant
文章编号:
5318
作者:
蒋大勇;?郭三学
武警工程大学装备管理与保障学院(陕西西安,710086)
Author(s):
JIANG Dayong;? GUO Sanxue
Equipment Management and Support College, Engineering University of PAP (Shaanxi Xi’an, 710086)
关键词:
安全工程;?磨料水射流;?HTPB推进剂;?切割效率;?参数优化
Keywords:
safety engineering;? abrasive water jet;? HTPB propellant;? cutting efficiency;? parameter optimization
分类号:
TJ410. 89
DOI:
10.3969/j.issn.1001-8352.2019.04.009
文献标志码:
A
摘要:
利用前混合磨料水射流,对高、低两种燃速的HTPB推进剂开展切割试验,着重研究不同切割条件下工艺参数对切割效率的影响,进而为工艺参数优化提供理论依据。选取切割速度(v)、出口压力(p)、磨料浓度比(T)和靶距(L)4个工艺参数为主要影响因素,以最大切割深度(H)作为切割效率的衡量指标,分别通过单因素试验和正交试验进行分析,进而完成工艺参数的优化。试验结果表明,最大切割深度随切割速度的增加而减小,且单位时间内的切割面积存在最佳值;随着出口压力的增加,最大切割深度在特定范围内近似线性增加,并逐渐趋于平缓;磨料浓度比与靶距和最大切割深度均存在最佳对应关系。正交试验结果表明,切割速度对指标影响较为显着,靶距等3个工艺参数的影响相对较小。该研究可为前混合磨料水射流作为HTPB推进剂的工程化处废技术提供理论支持。
Abstract:
Cutting test was used to HTPB propellant with high and low burning rates by using the pre-mixed abrasive water jet. Influence of process parameters on cutting efficiency under different cutting conditions was studied, and theoretical basis was provided for parameter optimization. Cutting process speed (v), outlet pressure (p), abrasive concentration ratio (T) and target distance (L) were selected as the main influencing factors, and the maximum cutting depth was used as the measurement index of cutting efficiency by single factor test method to analyze the reasons for their impact separately. On this basis, orthogonal experiments were carried out to optimize the process parameters. The results show that the maximum cutting depth decreases with the increase of cutting speed, and the cutting speed per unit time exists an optimum value; the maximum cutting depth increases with the outlet pressure, and increases linearly in certain range and tends to be steady; There are preferred correlations for both abrasive concentration and target distance. The optimization results of the orthogonal test show that the cutting speed has a significant influence on the index, while target distance and other parameters were minor factors. This study provides theoretical support for the pre-mixed abrasive water jet as an engineered waste technology for HTPB propellants.

参考文献/References:

[1]HASHISH M,DU PLESSIS M P. Prediction equations relating high velocity jet cutting performance to stand off distance and multiphase [J].Journal of Engineering for Industry,1979, 101(8): 311-318.
[2]蒋大勇.高压水射流切割HTPB推进剂的实验分析[J].解放军理工大学学报(自然科学版),2013,14(4):430-435.
JIANG D Y.Chipping performance of HTPB propellant by high pressure water jet[J]. Journal of PLA University of Science and Technology (Natural Science Edition),2013, 14(4): 430-435.
[3]蒋大勇.前混合磨料水射流切割HTPB推进剂的可行性研究[J].365bet在线网址_365bet网上娱乐网址_365bet手机网址多少,2019,48(1):42-46.
JIANG D Y.Feasibility study on cutting HTPB propellants with pre-mixed abrasive water jet [J]. Explosive Materials, 2019, 48(1): 42-46.
[4]耿鹏飞.高压水射流切割工艺参数的研究[D].秦皇岛:燕山大学,2011.
GENG P F.The research of high pressure water jet cutting process parameters[D].Qinhuangdao: Yanshan University, 2011.
[5]CHAO J,ZHOU G,LEA M C,et al.Characteristics of abrasive water jet generated surface and effects of cutting parameters and structure vibration[J]. Journal of Engineering for Industry,1995, 117(11): 516-525.
[6]WANG J.Abrasive waterjet machining of polymer matrix composites-cutting performance, erosive process and predictive models [J].International Journal of Advanced Manufacturing Technology,1999, 22(5): 757-768.
[7]WANG J. Machinability study of polymer matrix composites using abrasive waterjet cutting technology [J].Journal of Material Processing Technology,1999, 94(1):30-35.
[8]LIU H,WANG J.Analysis of the cutting performance in contouring using abrasivean waterjet [J].Chinese Journal of Mechanical Engineering,2002, 15 (2): 73-78.
[9]李震,李锋,汪建新.高压水射流技术及应用[J].机械工程师,2009(11):33-36.
LI Z, LI F, WANG J X. High pressure waterjet technique and its application [J].Mechanical Engineer.2009(11): 33-36.
[10]郭艳飞.热塑性工程塑料磨料水射流切割工艺研究[D].秦皇岛:燕山大学,2013.
GUO Y F.Study on process of thermoplastic engineering plastic with abrasive water jet cutting [D].Qinhuang dao: Yanshan University, 2013.
[11]HASHISH M.Cutting with abrasive water jets [J].Mechanical Engineering, 1984, 12(3): 60-69.
[12]宋拥政,温效康,梁志强.磨料水射流等现代切割技术的研究与分析[J].锻压机械,1994(4):50-54.
[13]王伟.高压磨料水射流切割碳纤维复合材料的试验研究[D].哈尔滨:哈尔滨理工大学,2015.
WANG W.Study on the experiment of carbon fiber composite materials with high-pressure AWJ cutting[D].Harbin: Harbin University of Science and Technology, 2015.

相似文献/References:

[1]蒋大勇①,白云②.磨料水射流切割防暴弹的试验研究[J].365bet在线网址_365bet网上娱乐网址_365bet手机网址多少,2018,47(01):43.[doi:10.3969/j.issn.1001-8352.2018.01.008]
 JIANG Dayong,BAI Yun.Experimental Study on Cutting Anti-riot Ammunition by Abrasive Water Jet[J].EXPLOSIVE MATERIALS,2018,47(04):43.[doi:10.3969/j.issn.1001-8352.2018.01.008]
[2]孟子纯①,仲倩①②,徐森①②,等.乳化炸药最小自持燃烧压力的影响因素研究[J].365bet在线网址_365bet网上娱乐网址_365bet手机网址多少,2018,47(02):12.[doi:10.3969/j.issn.1001-8352.2018.02.003]
 MENG Zichun,ZHONG Qian,XU Sen,et al.Research on Influencing Factors of Minimum Burning Pressure of Emulsion Explosives[J].EXPLOSIVE MATERIALS,2018,47(04):12.[doi:10.3969/j.issn.1001-8352.2018.02.003]
[3]蒋大勇.前混合磨料水射流切割HTPB推进剂的可行性研究[J].365bet在线网址_365bet网上娱乐网址_365bet手机网址多少,2019,48(01):42.[doi:10.3969/j.issn.1001-8352.2019.01.008]
 JIANG Dayong.Feasibility Study on Cutting HTPB Propellants with Pre-mixed Abrasive Water Jet[J].EXPLOSIVE MATERIALS,2019,48(04):42.[doi:10.3969/j.issn.1001-8352.2019.01.008]

备注/Memo

备注/Memo:
收稿日期:2018-12-12
基金项目:国家自然科学基金(51503224);武警工程大学“智能反恐防暴装备”团队基金
第一作者:蒋大勇(1981-),男,博士,副教授,主要从事含能材料的研究。E-mail:wanghe717@163.com
更新日期/Last Update: 2019-07-04